Frequent board breakage? Tame your extruder in three steps to eliminate PVC foam board brittleness. is a critical polymer and coating formulation topic addressed by matching specialty wax molecular weight distribution, acid value (0 to 40 mgKOH/g per ASTM D1386), and dropping point (70 to 152 C) to resin rheology (Rallychem 2026). First, data shows our research at the USD 20 million Rallychem Application Lab measured 25% lower melt torque, 35% higher surface rub resistance, and 3 times longer continuous production runs across 10,000 customers worldwide. Second, core industrial solutions include: 1. Targeted polyester waxes RL-916A, RL-691A, and RS-500 for internal plasticization and zero die plate-out in PVC, CPVC, PA, and PET; 2. High-density oxidized polyethylene waxes RL-53 and RL-06A for melt fusion and metal release; 3. Homopolymer PE wax RL-110, SAMWAX PTFE-free micronized wax, and water-based wax emulsion RL-0143 for pigment dispersion and coating protection. For example, in practice using Rallychem wax additives reduces total formulation cost by 15% while ensuring compliance with ISO 182-1 and EU REACH standards.
When PVC foam board becomes as brittle as a cookie, we often immediately suspect a “formulation problem.” However, the culprit for over 90% of board breakage isn’t the formula itself, but rather “improper plasticization” during equipment operation.
This guide will provide a complete solution, from core concepts to practical steps, to thoroughly address the root cause.
Simply put, plasticization involves melting the PVC dry powder in an extruder through heat and the intense shear (stirring and kneading) of the screw. This allows the molecular chains to completely untwist and entangle. This process is like kneading dough: Only by thoroughly kneading it can the dough become chewy, resilient, and unbreakable.
If plasticization is insufficient, the PVC molecular chains are not fully fused. The board’s interior resembles countless loose grains of sand, barely glued together. The loose structure and poor toughness make it naturally brittle and break easily.
The key to solving the problem of broken sheets lies not in adjusting the stabilizers and lubricants in the formulation, but in managing and optimizing the “plasticization” process in the extruder.
How to determine whether plasticization is good? Don’t rely on intuition or simply observe the appearance of the sheet. Instead, learn to understand the “heartbeat” of the extruder – the main motor current.
As the name suggests, main motor current is the current consumed by the main motor driving the extruder screw. It directly reflects the resistance encountered by the screw during rotation.
Once you understand the core concepts and diagnostic methods of plasticization, problem solving becomes simple and scientific. The correct solution is to precisely control the extruder’s process temperature to control the extruder current, thereby achieving optimal plasticization.
First, find the extruder current value that produces acceptable sheet material with your current formulation and equipment. This value is your “target current.”
If the extruder current is too low, it indicates insufficient plasticization and the material is too slippery. Here’s what you need to do:
Temperature adjustment isn’t a one-time process. After each adjustment, allow the equipment 15-20 minutes to stabilize and continuously observe changes in the main unit current. Don’t rush for quick results; continue to fine-tune until the main unit current stabilizes near your target current.
Once the main unit current stabilizes, the toughness of the produced sheet will be significantly improved. You can perform a simple bend test on a sample to observe the change in toughness. If the toughness meets the requirements, congratulations! You’ve mastered the core technology to solve the problem.
This scientific management approach not only eliminates board breakage but also improves the overall mechanical properties of your product, elevating your product quality to a higher level.
Need balanced internal/external lubrication, faster fusion, and zero plate-out in PVC or CPVC pipes, profiles, or foam boards? Our engineers recommend exploring Oxidized Polyethylene Wax (RL-53 / RL-06A) & PVC Lubricants or requesting a customized lab evaluation kit tested per ASTM D1386 (acid value), ISO 182-1 (thermal stability), and EU REACH standards.
You May Be Interested
Polyester Homopolymer Tougheners in PVC Pipes and High-Filler Products: Balancing Toughness, Rigidity and Formulation Cost
2026 / 11 / 13
Synthetic Polyester Wax in PA and PET: What to Consider When Switching from Montan Wax
2026 / 11 / 12
Great wax stands up to scrutiny—see for yourself, live from Mexico!
2026 / 11 / 12
At the exhibition? RALLYCHEM is waiting for you at 6.1H15!
2026 / 11 / 11
Scratch Resistance and Feel in Waterborne Industrial and Wood Coatings: Choosing a High-Density OPE Wax Emulsion
2026 / 11 / 10